This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch.
The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.
The board can be powered by a 0.9 to 7 V supply or battery and provides a linear, single-ended output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ADT001-10E quadrant rotation sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine digital quadrature outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ADT002-10E low-hysteresis quadrant rotation sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine digital quadrature outputs.
This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely.
A miniature bar magnet is included so you can see for yourself how these remarkable sensors work.
Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm.
These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT024-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM124-10E 0 to 1 mT Smart GMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface as well as a magnetic threshold output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM324-10E 0 to 1.5 mT precision Smart TMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and has a sophisticated I2C interface.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA003-02E 2 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
This evaluation board measures zero to seven amps with just four connections--two for the power supply and two for a differential output. The board is based on the revolutionary ALT023-10E TMR magnetometer, which is ideal for noncontact current sensing. The current-over-trace configuration provides inherent isolation and is more efficient than a shunt.
The board has a sensor plus 1/4" screw terminals for current connections, a standard 0.1-inch header for sensor connections, and a 1 mm pitch card-edge connector.
The board comes with a business-card size guide with pinouts and specifications. A QR code provides a link to the sensor datasheet.
The board measures 2.0" x 1.9" x 0.63" (52 x 48 x 1.6 mm)
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM125-10E 0 to 4 mT Smart GMR magnetometer sensor.
The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface as well as a magnetic threshold output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA006-00E 5 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.