A preassembled circuit board with a high-sensitivity AAH002-02E sensor and a differential amplifier circuit with a gain of 25. The board can be powered by a 2.7 to 12 V supply and provides a single-ended output with a typical sensitivity of 3.75 V/V/mT (375 mV/V/Oe).The circuit board is 12.5 x 7.8 mm, with Vcc, GND, and OUT plated-through holes for wires or a header.
This kit includes a 5-inch by 5-inch circuit board with an AAT003 Angle Sensor, 60 multicolor smart LEDs (6° spacing) to indicate rotation angle, and a preprogrammed, onboard ATtiny microcontroller.
The microcontroller also provides a PWM angle output. The board is factory calibrated and can optionally be field calibration.
A split-pole magnet, a magnet locating fixture, and a 5-volt wall mount power supply module are also included.
The board comes preprogrammed, but the Arduino compatible software is available on Github/NveCorporation so you can use the routines in your own application.
This self-contained module allows zeroing and programming the digital output threshold and hysteresis or SM124-10E or SM125-10E Smart Magnetometer without need of a computer or a customer microcontroller.
The 2.5" x 2.5" (64 mm x 64 mm) board has an I²C master microcontroller connected to the SM124.
A pushbutton for zeros the sensor, and miniature rotary thumbwheel switches provide three digits of resolution for the threshold and two for hysteresis. A custom TDFN-6 socket accommodates the 2.5 mm x 2.5 mm SM12x-10E. The module is powered by a small wall-mounted power supply (included).
Jumpers allow the sensor to be disconnected from the rest of the board so the board can be used as an interface to the customer’s electronics.
This module includes:
A 2.5 x 2.5 mm TDFN6 socket for a SM12x-10E Smart Magnetometer
A preprogrammed, onboard microcontroller
Two sets of thumbwheel switches for digital threshold and hysteresis
Two LEDs indicating the sensor’s output and successful programming
The AG956-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR002-10E Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR002-10E sensor
- a diametrical
magnet
- magnet fixturing and a
An interface board with:
- a microcontroller
connected to the sensor via SPI
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
The AG963-07E Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable ASR012-10E I2C Smart Angle Sensor. The kit includes:
An evaluation board with:
- an ASR012-10E sensor
- a diametrical
magnet
- magnet fixturing
An interface board with:
- a microcontroller
connected to the sensor via I²C
- flexibility to power
from USB or external power supply
- isolated USB interface
for safety and low noise.
A powerful, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a
computer.
The AG964-07E Demonstation Board has everything you need to evaluate
the remarkable ASR022-10E ABZ TMR Encoder Sensor. The demonstration includes:
ASR022-10E ABZ Noncontact TMR Encoder Sensor
A four-digit display to indicate rotation
Part # 12426 split-pole Alnico 5 round horseshoe magnet
LEDs for A, B, Z, and Direction outputs
Plastic magnet locating fixture
Powered by two AAA batteries (included)
The AG965-07E demonstration kit showcases micron precision with an AET500-02E sensor.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An AET500-02E 5 mm pole-pitch sensor
A four digit position display
Part #12592 5mm pole pitch magnetic tape
3-D printed fixturing
LEDs for pole detected
Powered by three AAA batteries (included)
The AG972-07E Demonstration Board showcases rotational encoding to
a few thousandths of a degree with an ABT375-00E sensor and a 30-tooth gear.
The kit includes:
A 3 x 5-inch (76 x 127 mm) PCB
An ABT375-00E gear tooth sensor
An eight-digit rotational display
a 30-tooth. 0.5 module gear
Part #12216 ceramic bias magnet
Test points for analog outputs
Powered by two AAA batteries (included)
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
An evaluation board with:
- an SM324-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
A powerful, intuitive graphical user interface.
Simple software installation.
Flexibility to power from USB or an external power supply.
Isolated USB interface for safety and noise minimization.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.