Sensor Evaluation Kits
ASR002-10E-EVB01: SPI TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR002-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use SPI interface.
- Part Number:
- ASR002-10E-EVB01
- Quantity in Stock:
- 30
$19.95
ASR012-10E-EVB01: I2C TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR012-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface.
- Part Number:
- ASR012-10E-EVB01
- Quantity in Stock:
- 30
$19.95
ASR022-10E-EVB01: ABZ TMR Smart Angle Sensor Eval Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR022-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 2.2 to 3.6 V supply and provides an encoder-compatible ABZ interface.
- Part Number:
- ASR022-10E-EVB01
- Quantity in Stock:
- 30
$19.95
AG958-07E: SM124 Smart GMR Magnetometer breakout board w/connector
The AG958-07E provides easy connections to an SM124-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG958-07E
- Quantity in Stock:
- 8
$24.95
AG961-07E: SM125 Smart GMR Magnetometer breakout board w/connector
The AG961-07E provides easy connections to an SM125-10E Smart GMR Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. A connector is provided to connect the board to the AG955-07E Self-Contained SM124/SM125 Programmer or customers' own boards. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
- Part Number:
- AG961-07E
- Quantity in Stock:
- 22
$24.95
ALT021-10E-EVB02: 0-0.25 mT TMR eval board w/amplifier
A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.
The board can be powered by a 0.9 to 7 V supply or battery and provides a linear, single-ended output.
- Part Number:
- ALT021-10E-EVB02
- Quantity in Stock:
- 38
$49.95
AG974-07E: ACT001-10E Isolated Current Sensor Evaluation Board
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
- Part Number:
- AG974-07E
- Quantity in Stock:
- 19
$50.00
AG001-01E: GMR Analog Sensor Evaluation Kit
The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.
- Part Number:
- AG001-01E
- Quantity in Stock:
- 5
$60.00
AG911-07E: GMR Switch Evaluation Kit
AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.
- Part Number:
- AG911-07E
- Quantity in Stock:
- 11
$65.00
AG920-07E: GT Sensor Evaluation Kit
The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.
- Part Number:
- AG920-07E
- Quantity in Stock:
- 8
$65.00
AG970-07E: AET-Series TMR Linear Sensor Eval Kit
The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:
• All five AET-Series parts (unsoldered in tubes)
• A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
• Detachable fixturing for linear magnetic tape (tape sold separately)
- Part Number:
- AG970-07E
$65.00
AG930-07E: AAT001 1.25 MOhm Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.
- Part Number:
- AG930-07E
- Quantity in Stock:
- 19
$70.00
AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit
The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.
The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.
- Part Number:
- AG903B-07E
$75.00
AG905-07E: ALT025 High Current PCB Demonstration
This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.
- Part Number:
- AG905-07E
$75.00
AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.
- Part Number:
- AG931-07E
- Quantity in Stock:
- 22
$75.00
AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.
- Part Number:
- AG933-07E
$75.00
AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit
The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.
- Part Number:
- AG934-07E
- Quantity in Stock:
- 1
$75.00
AG910-07E: GMR Switch Evaluation Kit w/ZIF socket
AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.
- Part Number:
- AG910-07E
- Quantity in Stock:
- 10
$90.00
AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator
A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".
- Part Number:
- AG921-07E
$90.00
AG932-07E: ADT002 Rotation Sensor Evaluation Kit
The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.
- Part Number:
- AG932-07E
- Quantity in Stock:
- 11
$90.00
