Sensor Evaluation Kits

Displaying 21 to 40 (of 80 products)
ADT925-14E TMR Switch USB business card demonstration

A smart business card that demonstrates the ADT925-14E 1.1 x 1.1 mm DFN4 TMR Switch sensor.

The board can be plugged into a USB TYPE-A connector, such as those on a computer, for power. An LED on the card shows when the sensor is activated. A small neodymium magnet is included to activate the sensor.

You can carry it with you so you're always prepared to demonstrate the high sensitivity, low power, and small size of TMR sensors.

Part Number:
ADT925-14E-EVB02
Quantity in Stock:
57

$19.95

AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board

This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040B
Quantity in Stock:
30

$19.95

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T
Quantity in Stock:
11

$19.95

AG957-07E: ASR002 Smart TMR Angle Sensor breakout board

The AG957-07E provides easy connections to an ASR002-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG957-07E

$19.95

AG967-07E: ASR022 ABZ Smart TMR Encoder Sensor breakout board

The AG967-07E provides easy connections to an ASR022-10E ABZ TMR Encoder Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.5 by 0.6 inches (12 x 15 mm).

Part Number:
AG967-07E
Quantity in Stock:
14

$19.95

AG968-07E: SM228 15 mT I2C Smart TMR Magnetometer Breakout Board

The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG968-07E

$19.95

AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board

The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).

Part Number:
AG975-07E

$19.95

AKT001-14E-EVB01: 1.5 T DFN4 TMR Magnetometor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AKT001-14E high-field (1.5 T), low power TMR analog bridge magnetometer. The sensor is an ultraminiature 1.1 x 1.1 mm package.

The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 5.5 V supply and provides a differential output voltage proportional to the applied magnetic field.

Part Number:
AKT001-14E-EVB01
Quantity in Stock:
50

$19.95

ALT002-14E-EVB01: 0-0.25 mT DFN4 TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT002-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT002-14E-EVB01
Quantity in Stock:
45

$19.95

ALT021-10E-EVB01: 0-0.25 mT TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT021-10E-EVB01
Quantity in Stock:
5

$19.95

ALT023-10E-EVB01: 0-1 mT TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT023-10E-EVB01
Quantity in Stock:
49

$19.95

ALT024-10E-EVB01: 0-2 mT TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT024-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT024-10E-EVB01
Quantity in Stock:
41

$19.95

ALT025-10E-EVB01: 0-10 mT DFN6 TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT025-10E-EVB01
Quantity in Stock:
13

$19.95

ALT025-14E-EVB01: 0-10 mT DFN4 TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT025-14E-EVB01
Quantity in Stock:
59

$19.95

ALT026-10E-EVB01: 0-20 mT DFN6 TMR magnetometor breakout board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT026-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer. The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.

Part Number:
ALT026-10E-EVB01
Quantity in Stock:
55

$19.95

ALT521-10E-EVB01: Ultrasensitive Two-Axis Rotational Sensor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT521-10E 2 MOhm Tunneling Magnetoresistance (TMR) Ultrasensitive Two-Axis Rotational Sensor.

The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a 1 mm pitch card-edge connector.

The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.

Part Number:
ALT521-10E-EVB01

$19.95

ASR002-10E-EVB01: SPI TMR Smart Angle Sensor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR002-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.

The board has a pre-soldered sensor, bypass capacitor as recommended, a standard 0.1" (2.54 mm) header and a mm pitch card-edge connector.

The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use SPI interface.

Part Number:
ASR002-10E-EVB01
Quantity in Stock:
27

$19.95

ASR012-10E-EVB01: I2C TMR Smart Angle Sensor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR012-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.

The board has a pre-soldered sensor, bypass capacitor as recommended, a standard 0.1" (2.54 mm) header and a mm pitch card-edge connector.

The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface.

Part Number:
ASR012-10E-EVB01
Quantity in Stock:
27

$19.95

ASR022-10E-EVB01: ABZ TMR Smart Angle Sensor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ASR022-10E Smart Tunneling Magnetoresistance (TMR) angle sensor.

The board has a pre-soldered sensor, bypass capacitor as recommended, a standard 0.1" (2.54 mm) header and a mm pitch card-edge connector.

The board can be powered by a 2.2 to 3.6 V supply and provides an encoder-compatible ABZ interface.

Part Number:
ASR022-10E-EVB01
Quantity in Stock:
25

$19.95

SM124-10E-EVB01: I2C 1 mT GMR Smart Sensor Breakout Board

A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the SM124-10E 0 to 1 mT Smart GMR magnetometer sensor. The board has a pre-soldered sensor, a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.

The board can be powered by a 2.2 to 3.6 V supply and provides an easy-to-use I2C interface as well as a magnetic threshold output.

Part Number:
SM124-10E-EVB01
Quantity in Stock:
46

$19.95

Displaying 21 to 40 (of 80 products)