Sensor Evaluation Kits

Displaying 1 to 20 (of 31 products)
AG040C: ADL021 Externally-Powered Nanopower Sensor Evaluation Board

This kit includes an evaluation board with the ultraminiature, ultralow-power ADL021 magnetic switch. The board has a digital output, and can be powered from a 3.3-volt nominal supply. An LED shows the output. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Typical sensor quiescent current is only 100 nA, the sensor operate point is 20 Oe, and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040C
Quantity in Stock:
1

$16.95

AG040B: ADL021 Battery-Powered Nanopower Sensor Demonstration Board

This kit includes a demo board with the ultraminiature, ultralow-power ADL021 magnetic switch. An LED shows the sensor output. The board is powered by a three-volt lithium coin cell (included), and the sensor quiescent power consumption is so low that the battery will last indefinitely. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. Sensor quiescent current is only 100 nA typical; the sensor operate point is 20 Oe; and the sensors are 1.1 mm x 1.1 mm. These miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040B
Quantity in Stock:
6

$19.95

AG040T: ADT923 3V Battery-Powered TMR Switch Demonstration Board

The AG040T Demonstration Board has an ADT923 TMR magnetic switch powered by a three-volt lithium coin cell (included). An LED to show the sensor output. The sensor’s low quiescent power allows the battery to last at least several years with occasional LED use. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The sensors are 1.1 mm x 1.1 mm x 0.35 mm, and these miniature evaluation boards are just 0.25 x 1.57 inches (6 x 40 mm).

Part Number:
AG040T
Quantity in Stock:
4

$19.95

AG001-01E: GMR Analog Sensor Evaluation Kit

The AG001-01E GMR Analog Sensor Evaluation Kit is designed for experimentation and development. The kit contains an assortment of 14 NVE analog sensors plus several printed circuit boards and various permanent magnets. It includes the high-sensitivity AAH002 sensor. The kit contains only RoHS compliant parts.

Part Number:
AG001-01E

$60.00

AG911-07E: GMR Switch Evaluation Kit

AG911-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. A magnet and circuit boards for mounting the parts are included.

Part Number:
AG911-07E
Quantity in Stock:
5

$65.00

AG920-07E: GT Sensor Evaluation Kit

The kit includes one of each of NVE's analog and digital GT Sensors, two DD001-12E signal processing ICs, and several circuit boards for fixturing and testing the sensors.

Part Number:
AG920-07E
Quantity in Stock:
1

$65.00

AG970-07E: AET-Series TMR Linear Sensor Eval Kit

The AG970-07E Evaluation Kit helps test a variety AET-Series sensors with linear magnetic scales. The kit includes:   • All five AET-Series parts (unsoldered in tubes)
  • A 3 x 4-inch (76 x 101 mm) PCB with test points and screw terminals
  • Detachable fixturing for linear magnetic tape (tape sold separately)

Part Number:
AG970-07E
Quantity in Stock:
5

$65.00

AG903B-07E: 0.75A/5A/50A GMR Current Sensor Evaluation Kit

The evaluation board includes three sensor over current-trace modules with three AAL024-10E TDFN current sensors.

The board measures 1.565" x 2.915" (40 mm by 74 mm), and includes three separable modules. The three modules are optimized to measure currents of 0-0.75A, 0-5A, and 0-50A.

Part Number:
AG903B-07E
Quantity in Stock:
10

$75.00

AG905-07E: ALT025 High Current PCB Demonstration

This demonstration features the ALT025 low hysteresis, high-speed TMR magnetometer and a high current PCB layout, optimized for the detection of +/- 200 amps. The board has sturdy screw terminal connections for current input, and it has header pins for sensor power and output.

Part Number:
AG905-07E
Quantity in Stock:
12

$75.00

AG930-07E: AAT001 1.25 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT001-10E 1.25 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture.

Part Number:
AG930-07E
Quantity in Stock:
13

$75.00

AG931-07E: AAT003 40 KOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT003-10E 40 kilohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT003-10E Angle Sensor's 20 kilohm output impedance is ideal for direct interface to microcontrollers.

Part Number:
AG931-07E
Quantity in Stock:
5

$75.00

AG933-07E: AAT009 6 MOhm Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT009-10E 6 megohm Angle Sensor and a unity-gain buffer amplifier. The circuit board can be powered with a 1.7 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT009-10E Angle Sensor has ultra-ultra low power consumption and is ideal for long-term battery-powered operation or operation from harvested power.

Part Number:
AG933-07E
Quantity in Stock:
7

$75.00

AG934-07E: AAT101 Full-Bridge Angle Sensor Evaluation Kit

The kit includes a circuit board with an AAT101-10E Full-Bridge Angle Sensor, which provides two differential analog outputs, 90 degrees out of phase. The circuit board can be powered with a 0 V to 5.5 V power supply. An angular reticle on the circuit board aids in characterizing output versus angle. The kit also includes a split-pole magnet and a plastic magnet locating fixture. The AAT101-10E Angle Sensor typical output amplitude is 400 mV/V peak-to-peak for each output.

Part Number:
AG934-07E
Quantity in Stock:
6

$75.00

AG940-07E: Digital/Analog/Omnipolar/Bipolar Sensor Demo Board

The kit includes a demo board with our most popular sensor types: digital, analog, omnipolar, and bipolar. Each sensor drives an indicator LED. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by two coin cells (included).

Part Number:
AG940-07E

$75.00

AG910-07E: GMR Switch Evaluation Kit w/ZIF socket

AG910-07 kit includes several MSOP GMR Switches with different magnetic operate points and different output options such as current sink and current source. Magnets, circuit boards for mounting the parts, and a zero insertion force (ZIF) socket are also included.

Part Number:
AG910-07E
Quantity in Stock:
10

$90.00

AG921-07E: AKL001 Gear-Tooth Sensor Demonstrator

A self-contained demonstrator for NVE’s unique AKL digital gear tooth sensor.The battery-powered demonstrator (battery included) is based on an AKL001 sensor. The demonstrator also includes a circuit board with an LED and driver, a biasing magnet, and a gear that can be turned by hand. No assembly required. Dimensions 3" x 3" x 1.5".

Part Number:
AG921-07E
Quantity in Stock:
5

$90.00

AG932-07E: ADT002 Rotation Sensor Evaluation Kit

The kit includes a circuit board with an ADT002 low hysteresis, ultralow-power rotation sensor, a split-pole magnet that can be turned, and simple circuitry to drive LEDs from the sensor outputs. Two LEDs follow the sensor outputs; four others indicate the rotational quadrant. A 3-volt coin cell (included) powers the board.

Part Number:
AG932-07E
Quantity in Stock:
8

$90.00

AG941-07E: ADL-Series Sensor Demo Board

The kit includes a demo board with three ultraminiature, ultralow-power ADL-Series magnetic sensors. Each sensor drives an indicator LED, and a meter shows the sensor power in microamps or nanoamps. A miniature bar magnet is included so you can see for yourself how these remarkable sensors work. The evaluation boards are 3.75 x 5 inches (95 x 127 mm), and are powered by a coin cell (included).

Part Number:
AG941-07E
Quantity in Stock:
4

$90.00

AG952-07E: SM124-10E Smart GMR Magnetometer Evaluation Kit

The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM124-10E sensor.
          - a microcontroller connected to the sensor via I²C.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG952-07E
Quantity in Stock:
12

$95.00

AG953-07E: SM225-10E Smart TMR Magnetometer Evaluation Kit

The AG953-07 Evaluation Kit has everything you need to test and evaluate the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
    • A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
          - an SM225-10E sensor.
          - a microcontroller connected to the sensor via SPI.
          - a current-carrying trace under the sensor for evaluating as a current sensor.
    • A PWM board output for an analog representation of the measured magnetic field.
    • A simple, intuitive graphical user interface.
    • Simple software installation.
    • USB cable to connect the Evaluation Board to a computer.
    • A small ceramic magnet for evaluating as a proximity sensor.

Part Number:
AG953-07E
Quantity in Stock:
8

$95.00

Displaying 1 to 20 (of 31 products)