A smart business card that demonstrates the ADT925-14E 1.1 x 1.1 mm DFN4 TMR Switch sensor.
The board can be plugged into a USB TYPE-A connector, such as those on a computer, for power. An LED on the card shows when the sensor is activated. A small neodymium magnet is included to activate the sensor.
You can carry it with you so you're always prepared to demonstrate the high sensitivity, low power, and small size of TMR sensors.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ACT001-10E TMR analog bridge current sensor. The sensor
has an on-chip current strap for precise operation.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 14 V supply and provides a differential output voltage proportional current.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT101-10E Full-Bridge Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides full-bridge sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT009-10E 6 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and draws less than a microwatt. It provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT006-10E1.5 mT, 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT003-10E40 kOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAT001-10E 1.25 MOhm Tunneling Magnetoresistance (TMR) analog angle sensor.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 5.5 V supply and provides sine and cosine analog outputs.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAL024-10E 1.5 mT saturation, low hysteresis GMR analog bridge magnetometer. Its cross-axis sensitivity makes it ideal for noncontact current sensing, which can be evaluated using this board (up to 7 A for this board).
The board has a pre-soldered sensor, screw terminals for the current trace, a standard 0.1" (2.54 mm) header, and a 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field or current.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAL004-10E 1.5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAL002-02E 1.5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAH004-00E 1.5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AAH002-02E ultrahigh-sensitivity 0.6 to 3 mT linear range GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 12 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA007-00E 50 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA006-02E 5 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA006-00E 5 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA005-02E 10 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA004-02E 5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA004-00E 5 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA003-02E 2 mT saturation GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA002-02E 0.15 to 1.05 mT GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.