The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
An LED indicating the state of the threshold output.
A PWM board output for an analog representation of the measured magnetic field.
A simple, intuitive graphical user interface.
Simple software installation.
USB cable to connect the Evaluation Board to a computer.
A small ceramic magnet for evaluating as a proximity sensor.
This 2” x 2” square evaluation board allows you to test the remarkable
ACT001-10E current sensor and a common application circuit.
The ACT001-10E is a fully-isolated, inline current sensor with
an on-chip current strap. A Wheatstone bridge manufactured
with NVE’s state-of-the-art tunneling magnetoresistance (TMR)
sensor elements detects the magnetic field from the input current
across NVE’s unique polymer isolation barrier.
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
The AG976 demonstration board includes an ASR003-10E sensor, a diametrical magnet, magnet fixturing, and an interface board with a microcontroller. Four variable-brightness LEDs show the magnetic field strength in each direction.
Easy-to-install Windows software provides a graphical user interface showing the sensor output and allowing sensor parameters to be programmed.
The AG977-07E provides easy connections to an ASR003-10E TMR Smart Angle Sensor. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads.
The board is approximately 0.5 by 0.6 inches (12 x 15 mm).
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
A 0.5 x 0.3 inch (13 x 8 mm) evaluation board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a sensor and a 5x amplifier to provide a 2.5 V/V/mT output.
The board can be powered by a 0.9 to 7 V power supply or battery and provides a linear, single-ended output.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT023-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-14E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V power supply and provides a linear, differential output voltage.