Products meeting the search criteria
12590: 1 mm pitch magnetic linear scale tape, 1 x 20 cm
This magnetic scale tape is designed to be used with AET100F-00E 1 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.
- Part Number:
- 12590
$30.00
12591: 2 mm pitch magnetic linear scale tape, 1 x 20 cm
This magnetic scale tape is designed to be used with AET200-00E 2 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.
- Part Number:
- 12591
$30.00
12592: 5 mm pitch magnetic linear scale tape, 1 x 20 cm
This magnetic scale tape is designed to be used with AET500-00E 5 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.
- Part Number:
- 12592
$30.00
AA007-00E-EVB01: 50 mT MSOP8 GMR Magnetometor Breakout Board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the AA007-00E 50 mT saturation, low-power GMR analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 24 V supply and provides a differential output voltage proportional to the applied magnetic field.
- Part Number:
- AA007-00E-EVB01
$19.95
AG968-07E: SM228 15 mT I2C Smart TMR Magnetometer Breakout Board
The AG968-07E provides easy connections to an SM228-10E Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG968-07E
$19.95
AG975-07E: SM223 1.5 mT I2C Smart TMR Magnetometer Breakout Board
The AG975-07E provides easy connections to an SM223-10E high-sensitivity Smart Magnetometer. In addition to the sensor, the board has a recommended bypass capacitor and a six-pin header connected to each of the sensor I/O pads. The board is approximately 0.6 by 0.75 inches (15 x 19 mm).
- Part Number:
- AG975-07E
$19.95
SM124-10E: General-Purpose 1 mT Smart GMR Magnetometer, TDFN6
The SM124-10E Smart Magnetometer combines an omnipolar GMR sensor element with
with easy-to-use digital signal processing.
A digital output provides precise, programmable thresholds.
An I²C interface provides magnetic field data, as well as a
calibration interface. The device is factory calibrated for accuracy. Calibration coefficients are stored in internal nonvolatile memory.
All commands, data, and coefficients are a single byte, and a
slick, elegant data structure lets you get up and running with
a minimum of firmware.
Key features include:
• Can detect magnets more than 50 mm away
• I²C and digital threshold outputs
• 0-1 mT linear range
• 8-bit / 1% output resolution
• −40°C to +125°C operating range
• 5% FS accuracy for 0 to 85°C
• 10 kSps sample rate for fast response
• 6 mA typical supply current
• In-plane sensitivity more usable than Hall effect sensors
• Programmable offset and gain compensation
• Optional magnet temperature compensation
• 2.2 to 3.6 volt supply
• Ultraminiature 2.5 x 2.5 x 0.8 mm TDFN package
- Part Number:
- SM124-10E
$6.88
12589: 0.5 mm pitch magnetic linear scale tape, 1 x 20 cm
This magnetic scale tape is designed to be used with AET050F-00E 0.5 mm pitch linear sensor. 1 cm (0.4 inches) wide by 20 cm (8 inches) long.
- Part Number:
- 12589
- Quantity in Stock:
- 2
$30.00
12545: Holder for 8 mm dia. disk magnet
A machined-aluminum magnet holder for 8 mm dia. magnets such as part numbers 12527 and 12528 (sold separately).
Compatible with
AG93x-Series
and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.
Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.
- Part Number:
- 12545
- Quantity in Stock:
- 3
$70.00
12546: Holder for 4 mm dia. disk magnet
A machined-aluminum magnet holder for 4 mm dia. magnets such as part number 12526 (sold separately).
Compatible with
AG93x-Series
and AG956 Evaluation Kits for AAT, ADT, and ASR-Series angle and rotation sensors.
Outside dimensions 11 mm dia. x 22 mm tall, with a 6-32 threaded mounting hole. Includes 0-80 set screws, set-screw Allen wrenches, a nylon knob, and a clock hand to track rotation.
- Part Number:
- 12546
- Quantity in Stock:
- 3
$70.00
AG953-07E: SM225-10E Smart TMR Magnetometer Evaluation Kit
The AG953-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM225-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM225-10E sensor.
- a microcontroller connected to the sensor via SPI.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG953-07E
- Quantity in Stock:
- 3
$95.00
AG962-07E: SM125-10E Smart GMR Magnetometer Evaluation Kit
The AG962-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM125-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM125-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG962-07E
- Quantity in Stock:
- 3
$95.00
AG969-07E: SM228-10E Smart I²C TMR Magnetometer Evaluation Kit
The AG969-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM228-10E I2C Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a bus-bar for evaluating as a current sensor.
• An LED indicating the state of the threshold output.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG969-07E
- Quantity in Stock:
- 4
$95.00
AG952-07E: SM124-10E Smart GMR Magnetometer Evaluation Kit
The AG952-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the easy-to-use SM124-10E Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM124-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG952-07E
- Quantity in Stock:
- 5
$95.00
ALT021-10E-EVB01: 0-0.25 mT TMR magnetometor breakout board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT021-10E ultrahigh sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
- Part Number:
- ALT021-10E-EVB01
- Quantity in Stock:
- 5
$19.95
SM223-10E: High-Speed Smart TMR Magnetometer, 1.5mT, I2C, TDFN6
The SM223-10E Smart Magnetometer combines a Tunneling Magnetoresistance (TMR) sensor element with
sophisticated digital signal processing for a unique combination of speed and precision. An I2C interface provides data as well as an external programming interface, and allows setting a versatile digital threshold output.
Unlike awkward, old-fashioned Hall-effect sensors, TMR is sensitive in-plane for
optimal current sensing and easy mechanical interfaces. Key features include:
• 0 to 1.5 mT linear range
• Can detect magnets more than 150 mm away
• Simple I2C interface
• Programmable digital threshold output
• 2% of full-scale accuracy for 0 to 125°C
• Fast 10000 sample-per-second update rate
• Factory calibrated
• Programmable offset and gain compensation
• -40°C to +125°C operating range
• Ultraminiature 2.5 x 2.5 mm DFN6 package
- Part Number:
- SM223-10E
- Quantity in Stock:
- 5
$6.88
AG973-07E: SM223-10E Smart I²C TMR Magnetometer Evaluation Kit
The AG973-07 Evaluation Kit has everything you need to test and evaluate
the easy-to-use SM223-10E I2C Smart Magnetometer. The kit includes:
• A 1" x 1.6" (25 mm x 41 mm) evaluation board with:
- an SM228-10E sensor.
- a microcontroller connected to the sensor via I2C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• An LED indicating the state of the threshold output.
• A PWM board output for an analog representation of the measured magnetic field.
• A simple, intuitive graphical user interface.
• Simple software installation.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG973-07E
- Quantity in Stock:
- 6
$95.00
ALT025-10E-EVB01: 0-10 mT DFN6 TMR magnetometor breakout board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT025-10E Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
- Part Number:
- ALT025-10E-EVB01
- Quantity in Stock:
- 13
$19.95
AG951-07E: SM324-10E Smart TMR Magnetometer Evaluation Kit
The AG951-07 Evaluation Kit has everything you need to calibrate, test, and evaluate
the remarkable SM324-10E Smart TMR Magnetometer. The kit includes:
• An evaluation board with:
- an SM324-10E sensor.
- a microcontroller connected to the sensor via I²C.
- a current-carrying trace under the sensor for evaluating as a current sensor.
• A powerful, intuitive graphical user interface.
• Simple software installation.
• Flexibility to power from USB or an external power supply.
• Isolated USB interface for safety and noise minimization.
• USB cable to connect the Evaluation Board to a computer.
• A small ceramic magnet for evaluating as a proximity sensor.
- Part Number:
- AG951-07E
- Quantity in Stock:
- 20
$245.00
ALT024-10E-EVB01: 0-2 mT TMR magnetometor breakout board
A 0.8 x 0.4 inch (21 x 10 mm) breakout board with the ALT024-10E high sensitivity Tunneling Magnetoresistance (TMR) analog bridge magnetometer.
The board has a pre-soldered sensor and footprints for a standard 0.1" (2.54 mm) header and a common, 1 mm pitch card-edge connector.
The board can be powered by a 0 to 10 V supply and provides a linear, differential output voltage.
- Part Number:
- ALT024-10E-EVB01
- Quantity in Stock:
- 41
$19.95
