WEBVTT
Kind: captions
Language: en

00:00:00.801 --> 00:00:09.410
♪ A Bridge Over Troubled Water ♪

00:00:09.410 --> 00:00:10.490
We’re demonstrating a
pitch pipe organ

00:00:10.490 --> 00:00:15.540
with an H-bridge controlled DC gear motor
and an NVE Smart Angle Sensor

00:00:15.540 --> 00:00:18.110
providing the rotation feedback.

00:00:18.110 --> 00:00:27.800
The motion is fast and precise,
despite the motor’s rotational inertia.

00:00:27.800 --> 00:00:30.398
So we can have a brisk tempo.

00:00:30.398 --> 00:00:42.720
♪ Mary Had a Little Lamb ♪

00:00:42.720 --> 00:00:46.640
The motor driver
is an isolated full H-bridge.

00:00:46.640 --> 00:00:52.079
NVE DC-to-DC convertors 
power the high side.

00:00:52.079 --> 00:00:54.800
And NVE isolators 
isolate the H-bridge

00:00:54.800 --> 00:00:57.230
and drive the MOSFETs.

00:00:57.230 --> 00:01:02.190
Here’s a closer look
at the angle sensor.

00:01:02.190 --> 00:01:05.899
A magnet is glued to the pitch pipe,
and the ASR012 detects

00:01:05.899 --> 00:01:08.220
the rotating magnetic field.

00:01:08.220 --> 00:01:11.250
The sensor is noncontact and can be
up to seven millimeters

00:01:11.250 --> 00:01:14.620
away from an inexpensive ferrite magnet,

00:01:14.620 --> 00:01:17.750
so there is a lot of mechanical latitude.

00:01:17.750 --> 00:01:23.520
We have a free Web app
to check the magnet spacing.

00:01:23.520 --> 00:01:25.990
There are 13 pitch-pipe notes,
so the notes are

00:01:25.990 --> 00:01:29.330
about 28 degrees apart.

00:01:29.330 --> 00:01:33.190
Pitch pipes come in various keys--
we chose a C-to-C variant

00:01:33.190 --> 00:01:38.240
to match a C-to-C
piano keyboard.

00:01:38.240 --> 00:01:41.959
In other demos we used a simple,
single MOSFET motor drive.

00:01:41.959 --> 00:01:44.080
But you can’t reverse the motor,
and you

00:01:44.080 --> 00:01:47.990
can't short the motor
to drain the back EMF.

00:01:47.990 --> 00:01:50.200
Adding a second MOSFET
to form a half-bridge

00:01:50.200 --> 00:01:52.880
allows the load to be shorted.

00:01:52.880 --> 00:01:56.360
This requires P-channel MOSFET,
which are less common,

00:01:56.360 --> 00:01:58.990
and for this circuit,
the motor voltage must the same

00:01:58.990 --> 00:02:02.960
as the logic voltage,
which may be impractical.

00:02:02.960 --> 00:02:07.130
We can add level shifting with an
isolator and a DC-to-DC convertor.

00:02:07.130 --> 00:02:11.950
That allows different
load, logic, and gate voltages.

00:02:11.950 --> 00:02:15.530
The ultimate motor drive circuit
is an isolated full H-bridge,

00:02:15.530 --> 00:02:17.470
which allows us to
reverse the motor,

00:02:17.470 --> 00:02:20.860
short the motor for faster stopping,
or pulse-width modulate

00:02:20.860 --> 00:02:23.660
to control the motor voltage.

00:02:23.660 --> 00:02:27.730
This is the detailed reference design
we used for this demo.

00:02:27.730 --> 00:02:32.410
The H-bridge uses three isolators
for four isolation channels.

00:02:32.410 --> 00:02:35.256
The isolation allows us to drive
the high-side MOSFETs,

00:02:35.256 --> 00:02:37.387
and level-shift 
the low-side MOSFETs

00:02:37.387 --> 00:02:41.082
from 3.3 to six volts.

00:02:41.082 --> 00:02:43.114
The isolators
have low-impedance outputs

00:02:43.114 --> 00:02:46.990
to directly drive MOSFETs,
so there are no MOSFET drivers.

00:02:46.990 --> 00:02:49.390
The isolator inputs
on each side of the H-bridge

00:02:49.390 --> 00:02:51.934
are connected in series,
which guarantees

00:02:51.934 --> 00:02:55.560
two MOSFETs on the same side
won’t be ON at the same time.

00:02:55.996 --> 00:03:01.768
A LOW turns on the low-side MOSFETs;
a HIGH signal drives the high-side MOSFETs;

00:03:02.277 --> 00:03:06.893
tri-state turns off both
the high-side and low-side MOSFETs.

00:03:06.893 --> 00:03:08.506
The isolators are the
world’s smallest and have

00:03:08.506 --> 00:03:10.550
best-in-class common-mode
transient immunity,

00:03:10.550 --> 00:03:14.309
which allows fast switching
for high efficiency.

00:03:15.762 --> 00:03:20.730
The DC-DC convertors have a full
2.5 kilovolts rms of isolation,

00:03:20.730 --> 00:03:23.870
and are the smallest devices
of their type.

00:03:23.870 --> 00:03:27.100
Here’s the rest of the wiring diagram:

00:03:27.100 --> 00:03:29.920
An Arduino controls the system.

00:03:29.920 --> 00:03:32.260
The speed of the angle sensor
allows us to move the motor

00:03:32.260 --> 00:03:33.740
very quickly.

00:03:33.740 --> 00:03:43.120
The Arduino also connects to an air valve,
keyboard, mode switch, and LED array.

00:03:43.120 --> 00:03:45.810
Gear motors typically have
a lot of inertia.

00:03:45.810 --> 00:03:50.840
We ran a test of the H-bridge and motor
for reversing and stopping the motor.

00:03:50.840 --> 00:03:55.020
Here we pulse the motor and let it coast
by turning off all the MOSFETS.

00:03:55.020 --> 00:03:57.530
As you can see,
with a 20-millisecond pulse,

00:03:57.530 --> 00:04:02.460
the motor coasts for 250 milliseconds.

00:04:02.460 --> 00:04:04.770
With the H-bridge we can 
short the back EMF

00:04:04.770 --> 00:04:07.120
by turning on the low-side MOSFETS.

00:04:07.120 --> 00:04:11.990
Then it only takes
about 60 milliseconds to stop.

00:04:11.990 --> 00:04:19.060
Here’s the procedure to read the angle,
which is pretty simple.

00:04:19.060 --> 00:04:24.630
We have a proportional control
of the motor pulse width.

00:04:24.630 --> 00:04:31.150
Here are the key components
used for this demo:

00:04:31.150 --> 00:04:35.999
Key ILDC-Series 
DC-to-DC convertor specifications are:

00:04:35.999 --> 00:04:41.813
* a DFN6 version that’s
the world’s smallest isolated DC-DC convertor;

00:04:41.813 --> 00:04:46.590
* various output voltages--
we used the six-volt version in this demo;

00:04:46.590 --> 00:04:47.671
* soft start,

00:04:47.671 --> 00:04:51.256
so the controller can start
before the high-side is energized;

00:04:51.256 --> 00:04:52.810
* fully isolated;

00:04:52.810 --> 00:04:56.570
* and the full industrial temperature range.

00:04:56.570 --> 00:04:58.531
The IL600-Series isolators have:

00:04:58.531 --> 00:05:01.370
* ultrahigh CMTI;

00:05:01.370 --> 00:05:04.003
* extended 3 to 6.6-volt power supply range

00:05:04.003 --> 00:05:07.004
for direct-drive of six-volt MOSFET gates;

00:05:08.280 --> 00:05:10.241
* full isolation;

00:05:10.241 --> 00:05:11.877
* no input-side power supply; 

00:05:11.877 --> 00:05:15.653
* and ultraminiature packages.

00:05:15.944 --> 00:05:20.160
Finally, ASR-Series angle-sensor 
specifications include:

00:05:20.160 --> 00:05:22.180
* 0.1-degree precision;

00:05:22.180 --> 00:05:24.180
* wide field operating range;

00:05:24.180 --> 00:05:25.817
* high speed; 

00:05:25.817 --> 00:05:28.257
* and ultraminiature.

00:05:28.692 --> 00:05:31.590
Visit our Website
or email us for more information

00:05:31.590 --> 00:05:35.926
about our DC-to-DC convertors, isolators,
or sensors.

